Category:EtherCAT:EC SETUP

From SoftMC-Wiki
Revision as of 13:26, 4 January 2015 by Nigeller (talk | contribs)
Jump to: navigation, search

Category:EtherCAT:EC SETUP How to Set up EtherCAT.

The front page is EtherCAT

Introduction

Before starting to work with the softMC you must setup the EtherCAT master to work with the slaves.
You must configure the axes in the system in a certain manner, then invoke certain functions and subroutines in an orderly manner, and make sure no errors occur.

A CONFIG.PRG and a program file EC_SETUP.PRG exist in the repository, and demonstrate the following process.

CONFIG.PRG allocates an array of generic axes by the name Axes[], and sets all the existing axes in the system into this array.
EC_SETUP.PRG and AX_SETUP.PRG use this array to setup the system automatically.

IMPORTANT.svgIMPORTANT
It is critical to maintain the demonstrated order of the EtherCAT setup.
Any change in the given example may result in undefined behavior!

EC_SETUP.PRG

EC_SETUP.PRG is a generic script. Its purpose is to configure the EtherCAT master and slaves before they are started, start the master, and eventually run additional actions to complete the EtherCAT startup procedure.

EC_SETUP.PRG is written in a manner that easily allows embedding code to configure specific motion drives and IO modules.

This article details the main steps that occur upon EtherCAT startup as they are executed by EC_SETUP.PRG.

Drive Address

Each EtherCAT slave has an address. Currently this address is determined strictly according to the slave location in the physical topology of the system; that is, the first slave attached to the MC is assigned drive address 1, the second slave in the chain gets slave address 2, and so on.

An EtherCAT slave can be a motion drive or an IO module.

PRE-OP Mode

Before the master is started all the slaves are in PRE-OP mode. In this stage the master is created and the system gathers information from the slaves in order to create data structures that are used by the master to set up the EtherCAT communication.

First, differentiate between motion drives and IO modules. For each slave query the slave's Vendor ID and Product Code. This data can later be used to identify specific products and create specific configuration for them, as in the CDHD Configuration example. 

	numOfSlaves = EC_ETHERCAT_INIT

Look for an unknown generic DS402 motion drive. If found, remap its PDOs to the required minimum. 

	for drive_addr = 1 to numOfSlaves
		if ETSLAVES[drive_addr]->et_slavetype = ECAT_MOTIONSLAVE then
			if EC_SLAVES_INFO[drive_addr]->vendor_id = GENERIC_DS402_DRIVE_VENDOR then
				call EC_REMAP_MINIMUM_PDOS(drive_addr)
			end if
		end if
	next

Create the EtherCAT Master. 

	call EC_CREATE_MASTER

Set Motion Cycle Time: 4000, 2000, 1000, 500 or 250 [us] 

	call EC_SET_BUS_CYCLETIME(4000)   ' For a cycle time of 500/250[us], add to FWCONFIG: hpetfreq = 2000


From here on EC_SETUP.PRG uses the gathered information to configure the slaves. A 'For Loop' goes over the slaves and tries to match them to already known products (such as the CDHD). When found, product specific functions are invoked to create data structures in the master that elaborate the PDO mapping of the slaves, be it a motion drive or an IO module. This is where you can add your own code to configure your own EtherCAT slave. Just add another case to match your Vendor ID.

If a Servotronix (STX) CDHD servo motion drive is found, the function EC_INSTALL_STX_CDHD is invoked. This function sets certain parameters in the drive, creates the PDO map of the CDHD, and queries the drive's PNUM and PDEN to allow calculation of the Position Factor.

For a generic drive, a minimum PDO mapping and default values are used.

For more information about the CDHD configuration, refer to CDHD Configuration.

After the slave configuration is done, a few more subroutines are called sequentially to complete the master's preparation, and the master is started: 

	call EC_ASSIGN_PDOS_AUTO

	' After telling the master which slaves we want to work with, we create the PDO map
	call EC_CREATE_PDOS_MAP

	call EC_SET_CYCLETIME  ' Set EtherCAT cycle time

	' Raise slaves to OP-Mode
	call EC_STARTMASTER    ' Syncs clocks between the master and the slaves, and sets master's opmode to operational

The master attempts to raise all the slaves to OP Mode. If it fails, the procedure is stopped and an error is issued. If it is successful, EtherCAT communication is now online and EC_SETUP.PRG starts the second stage of configuration.

OP Mode

Again, a For Loop goes over all the slaves. When a motion drive is encountered, EC_SETUP.PRG attaches its drive address to an axis and attempts to clear its faults. 

	' Assign slave address to an axis
	Axes[Axis_Attached_To_Drive].dadd = drive_addr

	' Attempt to clear faults in the drives
	Try

		call EC_CLEAR_FAULTS(drive_addr)

	Catch Else

		' if clear faults failed due to PLL Sync Error, wait a little longer and retry
		if EC_SDO_READ(drive_addr, 0x603f, 0) = 0x7386 then
			printu "PLL Error in drive #. Sleeping 5 seconds and retrying to clear fault";drive_addr
			sleep 5000
			call EC_CLEAR_FAULTS(drive_addr)
		end if

	End Try

All the motion drives are set to Synchronous Position Mode: 

	' Set drives to sync position mode
	if EC_IS_PDO(Axes[Axis_Attached_To_Drive].dadd, 0x6060, 0) then
		call EC_PDO_WRITE(Axes[Axis_Attached_To_Drive].dadd, Modes_Of_Operation_6060h, 0, 8)
	else
		call EC_SDO_WRITE(Axes[Axis_Attached_To_Drive].dadd, Modes_Of_Operation_6060h, 0, 8, 8)
	end if


See Also


This category currently contains no pages or media.

Retrieved from "http://softmc.servotronix.com/index.php?title=Category:EtherCAT:EC_SETUP&oldid=125244"