Difference between revisions of "MC-Basic:TORQUE"
(AXY: new links) |
|||
| Line 1: | Line 1: | ||
| − | {{Languages}} | + | {{Languages|MC-Basic:TORQUE}} |
{{MC-Basic | {{MC-Basic | ||
|SHORT FORM= Torque | |SHORT FORM= Torque | ||
| Line 9: | Line 9: | ||
*If executed in a mode different than TORQUEMODE a note will be thrown, but the command will be executed as usual | *If executed in a mode different than TORQUEMODE a note will be thrown, but the command will be executed as usual | ||
| − | *Interpolates torque command ([[ | + | *Interpolates torque command ([[MC-Basic:element.TORQUECOMMAND|TCMD]]) value from its initial value to the given torque value. The interpolation is done using the value of '''min([[MC-Basic:axis.TORQUECHANGERATIO|TorqueChangeRatio]],[[MC-Basic:axis.TORQUECHANGERATIOMAX|TorqueChangeRatioMax]])''' value as a rate of TCMD value change. No additional smoothing is done. |
*The torque interpolation is done using same mechanisms as motion interpolation. Depending on the value of <''axis''>.StartType the interpolation will start after the previous torque command was given or immediately (same rules as move command).The value of inpos for the starttype will be ignored and GCOMP will be used instead. | *The torque interpolation is done using same mechanisms as motion interpolation. Depending on the value of <''axis''>.StartType the interpolation will start after the previous torque command was given or immediately (same rules as move command).The value of inpos for the starttype will be ignored and GCOMP will be used instead. | ||
| Line 29: | Line 29: | ||
* [[MC-Basic:axis.SUMTORQUE|SUMTORQUE]] | * [[MC-Basic:axis.SUMTORQUE|SUMTORQUE]] | ||
| − | * [[ | + | * [[MC-Basic:element.TORQUECOMMAND|TORQUECOMMAND]] |
* [[MC-Basic:axis.COUNTTORQUECOMMAND|COUNTTORQUECOMMAND]] | * [[MC-Basic:axis.COUNTTORQUECOMMAND|COUNTTORQUECOMMAND]] | ||
| Line 35: | Line 35: | ||
* [[MC-Basic:axis.COUNTTORQUEADDITIVECOMMAND|COUNTTORQUEADDITIVECOMMAND]] | * [[MC-Basic:axis.COUNTTORQUEADDITIVECOMMAND|COUNTTORQUEADDITIVECOMMAND]] | ||
| − | * [[ | + | * [[MC-Basic:element.TORQUEFEEDBACK|TORQUEFEEDBACK]] |
* [[MC-Basic:axis.COUNTTORQUEFEEDBACK|COUNTTORQUEFEEDBACK]] | * [[MC-Basic:axis.COUNTTORQUEFEEDBACK|COUNTTORQUEFEEDBACK]] | ||
Revision as of 12:50, 13 September 2017
| Language: | English • 中文（简体） |
|---|
- If executed in a mode different than TORQUEMODE a note will be thrown, but the command will be executed as usual
- Interpolates torque command (TCMD) value from its initial value to the given torque value. The interpolation is done using the value of min(TorqueChangeRatio,TorqueChangeRatioMax) value as a rate of TCMD value change. No additional smoothing is done.
- The torque interpolation is done using same mechanisms as motion interpolation. Depending on the value of <axis>.StartType the interpolation will start after the previous torque command was given or immediately (same rules as move command).The value of inpos for the starttype will be ignored and GCOMP will be used instead.
- During execution the value of isMoving will be nonzero. Values of axis PCMD, VCMD, ACCELCOMMAND are not affected.
Short form
Torque
Syntax
Torque <axis> <Torque Value> {TorqueChangeRatio=<value>} {TorqueChangeRatioMax=<value>} {StartType = Generator-Completed, Immediate, Super-Immediate}
Availability
Since Version 4.9.0
Type
<Torque Value> - double
Examples
Torque Ax1 10.1 StartType=Immediate
See Also