Difference between revisions of "MC-Basic:axis.TORQUEERRORSTOPTYPE"
m |
(AXY: new links) |
||
| (19 intermediate revisions by 4 users not shown) | |||
| Line 1: | Line 1: | ||
| + | {{Languages|MC-Basic:axis.TORQUEERRORSTOPTYPE}} | ||
{{MC-Basic | {{MC-Basic | ||
|SHORT FORM= | |SHORT FORM= | ||
| Line 7: | Line 8: | ||
|AVAILABILITY= | |AVAILABILITY= | ||
| − | + | Since Version 4.5.x | |
|DESCRIPTION= | |DESCRIPTION= | ||
| Line 17: | Line 18: | ||
2 (ONPATH) – Immediate stop, using maximum deceleration, on the path of the motion. This is useful for stopping group motion so that all axes remain on the original path of travel during the stop. For a single axis, the IMMEDIATE and ONPATH types of stop are the same. | 2 (ONPATH) – Immediate stop, using maximum deceleration, on the path of the motion. This is useful for stopping group motion so that all axes remain on the original path of travel during the stop. For a single axis, the IMMEDIATE and ONPATH types of stop are the same. | ||
| + | <s> | ||
3 (ENDMOTION) – No Stop profile. immediately disabling the axis. | 3 (ENDMOTION) – No Stop profile. immediately disabling the axis. | ||
| Line 22: | Line 24: | ||
5 (DecStopOnPath) – The stopping profile uses the DecStop value. | 5 (DecStopOnPath) – The stopping profile uses the DecStop value. | ||
| + | </s> | ||
| + | <font color="red"> [3, 4 and 5, below as in .STOPTYPE:] | ||
| − | |||
3 (ENDMOTION) – Stop at the end of the current motion command. | 3 (ENDMOTION) – Stop at the end of the current motion command. | ||
| + | |||
4 (ABORT) – Stop the current motion immediately and proceed to start next motion. Only the accepted motion commands are stopped. The commands following this type of stop will be executed regularly. | 4 (ABORT) – Stop the current motion immediately and proceed to start next motion. Only the accepted motion commands are stopped. The commands following this type of stop will be executed regularly. | ||
| + | |||
5 (DecStopOnPath) – The stopping procedure is started immediately according to DecStop value. This parameter is modal so its value must be updated before executing the motion command. | 5 (DecStopOnPath) – The stopping procedure is started immediately according to DecStop value. This parameter is modal so its value must be updated before executing the motion command. | ||
</font> | </font> | ||
| Line 32: | Line 37: | ||
| − | + | If TorqueErrorStopType is IMMEDIATE(1), ONPATH(2), ABORT(4) or DecStopOnPath(5), the axis is <b>disabled only if</b> the condition TE > TEMAX is also true <b>after</b> the stopping profile ends. | |
| − | + | If TorqueErrorStopType is ENDOFMOTION(3), the axis is always and immediately disabled when the condition TE > TEMAX is detected. | |
| − | In both | + | In both instances, disable is done according to the values of TorqueErrorDisableType. |
|TYPE= | |TYPE= | ||
| Line 61: | Line 66: | ||
|SEE ALSO= | |SEE ALSO= | ||
| − | * [[ | + | * [[Motion Dynamics]] |
| − | * [[ | + | * [[MC-Basic:axis.TORQUEERRORDISABLETYPE|axis.TORQUEERRORDISABLETYPE]] |
| − | * [[ | + | * [[MC-Basic:element.TORQUEFEEDBACK|TORQUEFEEDBACK]] |
| − | * [[ | + | * [[MC-Basic:axis.TORQUEFACTOR|axis.TORQUEFACTOR]] |
| − | * [[ | + | * [[MC-Basic:axis.TORQUEADDCOMMAND|axis.TORQUEADDCOMMAND]] |
| − | * [[ | + | * [[MC-Basic:axis.TorqueMax|axis.TORQUEMAX]] |
| − | * [[ | + | * [[MC-Basic:axis.TORQUEERRORFILTER|axis.TORQUEERRORFILTER]] |
| − | * [[ | + | * [[MC-Basic:axis.TORQUEERRORMAX|axis.TORQUEERRORMAX]] |
| − | * [[ | + | * [[MC-Basic:axis.TORQUEERROR|axis.TORQUEERROR]] |
| Line 75: | Line 80: | ||
| − | [[Category | + | [[Category:Motion Dynamics|TORQUEERRORSTOPTYPE]] |
Latest revision as of 12:56, 13 September 2017
| Language: | English • 中文（简体） |
|---|
Defines the torque-error collision procedure. TE > TEMAX stopping of the axis is done according to:
1 (IMMEDIATE) – Immediate stop, using maximum deceleration.
2 (ONPATH) – Immediate stop, using maximum deceleration, on the path of the motion. This is useful for stopping group motion so that all axes remain on the original path of travel during the stop. For a single axis, the IMMEDIATE and ONPATH types of stop are the same.
3 (ENDMOTION) – No Stop profile. immediately disabling the axis.
4 (ABORT) – Same as ONPATH.
5 (DecStopOnPath) – The stopping profile uses the DecStop value.
[3, 4 and 5, below as in .STOPTYPE:]
3 (ENDMOTION) – Stop at the end of the current motion command.
4 (ABORT) – Stop the current motion immediately and proceed to start next motion. Only the accepted motion commands are stopped. The commands following this type of stop will be executed regularly.
5 (DecStopOnPath) – The stopping procedure is started immediately according to DecStop value. This parameter is modal so its value must be updated before executing the motion command.
If TorqueErrorStopType is IMMEDIATE(1), ONPATH(2), ABORT(4) or DecStopOnPath(5), the axis is disabled only if the condition TE > TEMAX is also true after the stopping profile ends.
If TorqueErrorStopType is ENDOFMOTION(3), the axis is always and immediately disabled when the condition TE > TEMAX is detected.
In both instances, disable is done according to the values of TorqueErrorDisableType.
Short form
<axis>.TorqueErrorStopType
Syntax
?<axis>. TorqueErrorStopType
Availability
Since Version 4.5.x
Type
Integer
Range
0 to 5
Default
3 (ENDMOTION)
Scope
Configuration, Task or Terminal
Limitations
- Read/Write
- Modal only
Examples
?A1.TorqueErrroStopType