Difference between revisions of "CANopen Protocol"
m (→CANopen protocol) |
|||
| Line 14: | Line 14: | ||
* [[CANOpen:CAN SDO WRITE|CAN_SDO_WRITE]] - expedite download of 32-bit integer | * [[CANOpen:CAN SDO WRITE|CAN_SDO_WRITE]] - expedite download of 32-bit integer | ||
* [[CANOpen:CAN SDO WRITE REAL|CAN_SDO_WRITE_REAL]] - expedite download of single precision floating point number | * [[CANOpen:CAN SDO WRITE REAL|CAN_SDO_WRITE_REAL]] - expedite download of single precision floating point number | ||
| + | |||
*''' Controlling device state machine <br>''' | *''' Controlling device state machine <br>''' | ||
bus[0].phase = 0 ' put CAN device to PREOP mode<br> | bus[0].phase = 0 ' put CAN device to PREOP mode<br> | ||
| Line 29: | Line 30: | ||
* Optional Digital Inputs and Outputs<br> | * Optional Digital Inputs and Outputs<br> | ||
PDO mapping and association between above mentioned objects and internal data structures of softMC is shown in the example [[Program_Examples:CANOpen:DS402_CAN_Drive_Setup]]<br> | PDO mapping and association between above mentioned objects and internal data structures of softMC is shown in the example [[Program_Examples:CANOpen:DS402_CAN_Drive_Setup]]<br> | ||
| − | corresponding firmware function are listed in Category:CANOpen:Firmware-Functions [[Category:CANOpen:Firmware-Functions]] | + | corresponding firmware function are listed in Category:CANOpen:Firmware-Functions [[Category:CANOpen:Firmware-Functions]] |
| + | |||
'''Synchronization'''<br> | '''Synchronization'''<br> | ||
For every bus cycle softMC broadcasts SYNC message to the devices and then sends to every slave a TX PDO that contains control word, target position and optional digital otputs. The motion controller expects all devices to send its TX PDO with the status word and the position feedback before the next SYNC.<br> | For every bus cycle softMC broadcasts SYNC message to the devices and then sends to every slave a TX PDO that contains control word, target position and optional digital otputs. The motion controller expects all devices to send its TX PDO with the status word and the position feedback before the next SYNC.<br> | ||
A bus cycle is triggered by a hardware timer therefore SYNC messages are sent to the slaves with low jitter that should not exceed 70 usecs.<br> | A bus cycle is triggered by a hardware timer therefore SYNC messages are sent to the slaves with low jitter that should not exceed 70 usecs.<br> | ||
| − | Devices shall lock their PLLs to the softMC SYNC cycle and tolerate SYNC jitter of up to 100 usecs. | + | Devices shall lock their PLLs to the softMC SYNC cycle and tolerate SYNC jitter of up to 100 usecs. |
| − | '''Bus cycle example: | + | |
| + | '''Bus cycle example:''' | ||
<Start cycle><br> | <Start cycle><br> | ||
MasterTPDO1<br> | MasterTPDO1<br> | ||
Revision as of 07:58, 21 August 2014
CANopen protocol
softMC provides a number of categories of services that allow operation of CANopen device.
- Upload and Download service objects
Application can read(upload) from or write (download) to device CANopen service data objects using either segmented or expedite SDO upload/download mechanism.
Those functions are implemented in CANOPEN.LIB
- CAN_SDO_READ_STRING - segmented upload of byte array
- CAN_SDO_READ - expedite upload of 32-bit integer
- CAN_SDO_READ_REAL - expedite upload of single precision floating point number
- CAN_SDO_WRITE_STRING - segmented download of byte array
- CAN_SDO_WRITE - expedite download of 32-bit integer
- CAN_SDO_WRITE_REAL - expedite download of single precision floating point number
- Controlling device state machine
bus[0].phase = 0 ' put CAN device to PREOP mode
bus[0].phase = 4 ' put CAN device to OP mode
- Configuration of motion objects
SoftMC requires DS402 compliant digital drive that supports following modes of operation and objects
- Mandatory Cyclic Synchronous Position mode (so-called opmode 8)
- Optional Cyclic Synchronous Torque mode mode
PDO map-able objects
Device shall provide following objects, object numbers may be different from standard.
- Control Word - object 0x6040.0
- Status Word - object 0x6041.0
- 32-bit Target position - object 0x607a.0
- 32-bit Position feedback - object 0x6064.0
- Optional Digital Inputs and Outputs
PDO mapping and association between above mentioned objects and internal data structures of softMC is shown in the example Program_Examples:CANOpen:DS402_CAN_Drive_Setup
corresponding firmware function are listed in Category:CANOpen:Firmware-Functions
Synchronization
For every bus cycle softMC broadcasts SYNC message to the devices and then sends to every slave a TX PDO that contains control word, target position and optional digital otputs. The motion controller expects all devices to send its TX PDO with the status word and the position feedback before the next SYNC.
A bus cycle is triggered by a hardware timer therefore SYNC messages are sent to the slaves with low jitter that should not exceed 70 usecs.
Devices shall lock their PLLs to the softMC SYNC cycle and tolerate SYNC jitter of up to 100 usecs.
Bus cycle example:
<Start cycle>
MasterTPDO1
MasterTPDO2
Dummy message
SYNC
..
..
Device1 TDPDO1
Device1 TDPDO2
..
DeviceN TDPDO1
DeviceN TDPDO2
<Start cycle>