Difference between revisions of "Program Examples:Homing/zh-hans"
(Created page with "{{Languages}} The following example demonstrates how to issue a homing procedure on all the axes. A "For Loop" iterates over the axes that are attached to motion drives, sets...") |
|||
| Line 1: | Line 1: | ||
| − | {{Languages}} | + | {{Languages|Program_Examples:Homing}} |
| − | + | 以下示例演示如何在所有轴上发出回零过程。 | |
| − | + | "For Loop"循环遍历连接到运动驱动器的轴，设置所需的归位参数，并调用[[EtherCAT:EC_SLAVE_HOME|EC_SLAVE_HOME]]启动回零过程。 | |
| − | + | ||
| − | {{Note| | + | {{Note|必须在“驱动单元”中设置回零参数，因此通过将用户值乘以相关的运动因子和1000倍的乘积，将用户值转换为驱动单位，从秒到毫秒。}} |
| − | |||
| − | |||
| Line 80: | Line 78: | ||
| − | + | 该示例对应于在GIT中的提交的SHA-1: 4fe3c7018de141d855eb556d3e637e0283807314 in GIT. | |
| − | == | + | == 参见 == |
* [[EtherCAT:EC SLAVE SET HOMING PARAMETERS|EC_SLAVE_SET_HOMING_PARAMETERS]] | * [[EtherCAT:EC SLAVE SET HOMING PARAMETERS|EC_SLAVE_SET_HOMING_PARAMETERS]] | ||
* [[EtherCAT:EC SLAVE GET HOMING PARAMETERS|EC_SLAVE_GET_HOMING_PARAMETERS]] | * [[EtherCAT:EC SLAVE GET HOMING PARAMETERS|EC_SLAVE_GET_HOMING_PARAMETERS]] | ||
* [[EtherCAT:EC_SLAVE_HOME|EC_SLAVE_HOME]] | * [[EtherCAT:EC_SLAVE_HOME|EC_SLAVE_HOME]] | ||
* [[EtherCAT:EC_INSTALL_STX_CDHD|EC_INSTALL_STX_CDHD]] | * [[EtherCAT:EC_INSTALL_STX_CDHD|EC_INSTALL_STX_CDHD]] | ||
Latest revision as of 05:42, 17 July 2017
| 语言: | English • 中文（简体） |
|---|
以下示例演示如何在所有轴上发出回零过程。
"For Loop"循环遍历连接到运动驱动器的轴，设置所需的归位参数，并调用EC_SLAVE_HOME启动回零过程。
 | NOTE |
| 必须在“驱动单元”中设置回零参数，因此通过将用户值乘以相关的运动因子和1000倍的乘积，将用户值转换为驱动单位，从秒到毫秒。 |
'**************************************************************************************************
' File: HOME.PRG
' Purpose: Home all the drives
' Version: 1.00
' Author: Nir Geller
' Global Variables Used: num_Of_Motion_Drives as long - Number of ECat MOTION DRIVES found by EC_SETUP.PRG
' Axes[64] - An array that holds all the axes in the system. Defined in CONFIG.PRG
' History: 9.11.14 - Created
' Description: This program example iterates over the axes and calls homing procedure.
' The homing parameters setting and the homing procedure is CDHD specific
'**************************************************************************************************
'************** Explanation **************
' Before starting the homing procedure the user must set homing parameters in the drive.
' These parameters must be in "drive units", therefore, the desired homing velocity is translated to
' drive units by multiplying it by the velocity factor and by a factor of 1000 in order to scale from
' seconds to milliseconds. The same is done for homing acceleration.
'**********************************************************************************************
Program
dim dHomingFactorFast as double = 0.5
dim dHomingFactorslow as double = 0.25
dim dHomingFactorAcc as double = 0.1
dim dSec2msec as double = 1000 ' this is used to convert from typical user time-units [msec] to typical drive time-units [sec]
dim dHomingVelocity as double = 0
dim dHomingAcceleration as double = 0
dim i as long = 0
' **** Home all the drives ****
for i = 1 to num_Of_Motion_Drives
attach Axes[i]
' **** Set homing parameters ****
' set homing method = 34 (pulse index, positive direction)
call EC_SLAVE_SET_HOMING_PARAMETERS(Axes[i], HOMING_METHOD, 34)
' set homing offset
call EC_SLAVE_SET_HOMING_PARAMETERS(Axes[i], HOMING_OFFSET, 0)
' set FAST homing speed = 10
dHomingVelocity = (Axes[i].VCruise * Axes[i].VFac * dSec2msec) * dHomingFactorFast
call EC_SLAVE_SET_HOMING_PARAMETERS(Axes[i], FAST_HOMING_SPEED, dHomingVelocity)
' set SLOW homing speed = 2
dHomingVelocity = (Axes[i].VCruise * Axes[i].VFac * dSec2msec) * dHomingFactorSlow
call EC_SLAVE_SET_HOMING_PARAMETERS(Axes[i], SLOW_HOMING_SPEED, dHomingVelocity)
' set homing acceleration/deceleration
dHomingAcceleration = (Axes[i].amax * Axes[i].afac * dSec2msec^2) * dHomingFactorAcc
call EC_SLAVE_SET_HOMING_PARAMETERS(Axes[i], HOMING_ACCELERATION, dHomingAcceleration)
call EC_SLAVE_HOME(Axes[i], 120000) ' Homing timeout: 120,000 msec
Axes[i].en = 0
detach Axes[i]
next
End Program
该示例对应于在GIT中的提交的SHA-1: 4fe3c7018de141d855eb556d3e637e0283807314 in GIT.