Difference between revisions of "PLS SETUP PROCEDURE/zh-hans"
| Line 1: | Line 1: | ||
| − | {{Languages}} | + | {{Languages|PLS_SETUP_PROCEDURE}} |
以下示例演示了PLS数据结构的设置。 | 以下示例演示了PLS数据结构的设置。 | ||
| Line 8: | Line 8: | ||
| − | 有关PLS的完整说明，请参阅[[Programmable Limit Switch | + | 有关PLS的完整说明，请参阅[[Programmable Limit Switch|Programmable Limit Switch]]. |
| Line 123: | Line 123: | ||
== 参见 == | == 参见 == | ||
| − | * [[Programmable Limit Switch | + | * [[Programmable Limit Switch|PLS]] |
* [[MC-Basic:pls.PLSPropagationDelay|PLS Propagation Delay]] | * [[MC-Basic:pls.PLSPropagationDelay|PLS Propagation Delay]] | ||
* [[MC-Basic:pls.PLSPropagationEnableDelay|PLS Propagation Enable Delay]] | * [[MC-Basic:pls.PLSPropagationEnableDelay|PLS Propagation Enable Delay]] | ||
Latest revision as of 11:17, 16 October 2018
| 语言: | English • 中文（简体） |
|---|
以下示例演示了PLS数据结构的设置。
 | IMPORTANT |
| PLS数据对象必须在CONFIG.PRG中定义:
Common Shared <PLS Name> as PLS <Axis> System.Dout.<DOut number> 例如: Common Shared Demo_PLS1 as PLS A1 System.Dout.1 |
有关PLS的完整说明，请参阅Programmable Limit Switch.
Program
call SetAxis
try
Demo_PLS1.PlsEnable = OFF
catch 3163 ' PLS value cannot be accessed before the pls data is created
Print "CreatePlsData not done!"
end try
CreatePlsData 2 Demo_PLS1 ' 2 points to toggle PLS
Demo_PLS1.PlsPosition[1] = 100.0
Demo_PLS1.PlsPosition[2] = 250
Print "PLS position 1: "; Demo_PLS1.PlsPosition[1]
Print "PLS position 2: "; Demo_PLS1.PlsPosition[2]
Print "Polarity: "; Demo_PLS1.PlsPolarity
Print "PLS-Repeat: "; Demo_PLS1.PlsRepeat
'Demo_PLS1.PlsRepeat = 1000 'Repeat distance e.g. for endless axes, switch all 1000mm
Print "PLS-Hysteresis: "; Demo_PLS1.PlsHysteresis
'Demo_PLS1.PlsHysteresis = 0.01 'necessary if the axis must stop at PLS position
Print A1.PlsSource
Attach A1
A1.PlsSource = A1.Pfb
Detach A1
' Print "PLS-Axis : "; Demo_PLS1.PlsAxisname
Print Demo_PLS1.PlsAxisname
' Print "PLS-Output: "; Demo_PLS1.PlsOutput
Demo_PLS1.PlsOutput = Sys.DOut.1
Print Demo_PLS1.PlsOutput
Print "PLS-Active: "; Demo_PLS1.PlsEnable
Demo_PLS1.PlsPolarity = ON 'switch default SignalOutput-Status to OFF
Demo_PLS1.PlsEnable = ON
Print "PLS-Active: "; Demo_PLS1.PlsEnable
End Program
sub SetAxis
with A1
attach
Simulated = 1
en = 0
sleep 1000
Vmax = 3000
VelocityOverride = 100
VelocityOverspeed = 3600
VRate = 100
ARate = 100
DRate = 100
JRate = 100
Vcruise = 3000
'VelocityJog = 100
Amax = 30000
Acc = 30000
Dmax = 30000
Dec = 30000
Jmax = 948000
Jerk = 948000
Cp = 0.0000
BlendingMethod = 1
BlendingFactor = 100
Pfac = 6400
Vfac = 6.4
Afac = 0.0064
Jfac = 0.0000064
Feedback = 0
PmaxEn = 1
Pmax = 495
PminEn = 1
Pmin = -10
PeMax = 1000000000000000000000
PositionErrorDelay = 3
PositionErrorSettle = 0.1
TimeSettle = 4
TimeSettleMax = 992
Direction = 1
Wrap = 0
Absolute = 1
detach
end with
end sub
该示例对应于在GIT中的提交的SHA-1: 33f496b1c050f69ee648413402ce11c9fab95820。